If you are installing a new toilet, it will have to be assembled and instructions. Follow the instructions that came with your toilet. Disconnect the tank from the bowl by removing the bolts found inside the bottom of the tank. Use a small adjustable wrench to disconnect the toilet stop nut (Image 1). When replacing a new toilet or installing a new one, it is important to make sure the toilet you have will fit in the space provided. On the inside of the tank, the tank lever is connected to a chain which operates the flapper. When water in the tank is filled to its set level, the float ball shuts the valve, preventing any more water from entering the tank.Ī tank trip lever is connected to the flush handle found on the outside of the tank. The float ball controls the flow of water from the water pipe directly to the tank and the flapper regulates the amount of water entering the bowl from the tank. Both the float ball and flapper control the flow of water. The other end of the ballcock is connected to the float ball. Water flows into the tank through an intake valve and is connected to the ballcock, which controls the water level inside the tank. A flange at the bottom of the toilet bowl secures the toilet to the floor and a wax gasket seals the bowl to the flange in order to prevent any water leakage. A tank- to- bowl gasket is required to make a successful connection from the tank to the toilet bowl, which must then be firmly secured by bolts and nuts. The tank is the unit that holds the water supply used for the flushing mechanism and the bowl brings in water from the tank when a flush occurs. The toilet tank and bowl work hand in hand. Knowledge of these various parts could save both time and money on potential repairs. Toilets contain many parts that allow them to operate effectively. But if you see these solutions not working, it might be high time to tap on the expertise of the professionals.Toilet Parts - Plumbing Supplies. Reconnect and turn the water supply back on to refill the tank, ensuring that the lid is put back into place.Īfter some time you have completed the task, check the bolts for leaks, and if there is any, you might need to perform the task once again.īy following these simple steps, you will be able to fix leaking tank bolts. Fasten the bolts and then check that the tank is connected properly, staying perpendicular to the housing of the bowl. Raise the tank back over the bowl housing and reset the central tank gasket and bolts correctly.

Re-Install The Toilet Tank And Its Refill.

Replace the washers and nut on the second bolt in the same order.Ħ.

Add a new metal washer to secure the tank to the toilet bowl housing.

Attach a new the bolt nut to the bolt and add the third rubber washer.

Put on the second rubber washer on the bolt on the outside of the tank.

Insert the bolt into the tank bolt hole.

Put one rubber washer on the bolt directly under the bolt head.

Attach the new rubber washers following these steps: Replace The Old Washers.Īfter completing the above-mentioned steps, extract the bolts from the toilet tank, making sure that you remove all the old rubber washers. When the tank is heavy, it is best to get someone to help you with lifting the tank straight up and carrying it to the padded surface.

Lift The Tank Off And Set It On a Padded Surface. To make the job easier, you can apply some penetrating oil to loosen the nuts from the bolts and release them from the bowl’s housing.Ĥ. Using an adjustable wrench, loosen the nuts from the bolts, and if they are stuck, you can get a helper to turn the bolts with the screwdriver from inside the tank, while you are holding the nut with the wrench. When you remove the toilet tank lid, set it aside on a pile of towels or blankets and leave room for the tank. You can get rid of the remaining water in the bowl by absorbing it with a sponge or a towel. Empty the bowl completely by flushing the toilet, and using the adjustable wrench, pull clear the water supply line of the tank. Drain The Toilet Tank Of Remaining Water.įirst, you have to make sure you have cut the water supply to the toilet by shut off the valve that is located behind the toilet bowl.

Here are steps you can follow to replace these components: 1. This means that you should replace the bolts, and possibly the nuts and washers, given that they are corroded or rusted. Water leaks on the bolts and nuts, as well as on the floor underneath them, would show you that the toilet tank bolts need new washers. Over time flushing your toilet, its tank bolts might start to leak as the rubber washers used in it would wear out.

How to install toilet tank bolts video